Virtual Output

Virtual is one of the five output devices a display can be routed to (alongside GPU, SDI, ST 2110, and NDI® — see Adding Displays). Where the other four routings deliver pixels to physical hardware or to the network, Virtual routes the captured pixels into an internal texture buffer that lives only inside the show. The buffer can then be used as a media source in other cues, fed through a wall processor to LED tiles, or mapped onto 3D geometry.

Virtual outputs are a core production tool for pixel mapping, content re-routing, and layered compositing workflows. They are not temporary placeholders — they remain in production shows alongside physical outputs.

What Makes an Output Virtual

A display's output is virtual when its Output Type is set to Virtual. In practical terms, a virtual output:

• Is not tied to a physical GPU, SDI, ST 2110, or NDI connector
• Does not require a node assignment
• Is always enabled (the enable/disable toggle is hidden)
• Can be placed, sized, and edited like any other display
• Can be used as a media source in cue workflows

When to Use Virtual Displays

LED Wall Pixel Mapping

Virtual displays are widely used for mapping content onto LED walls through a wall processor. Place a virtual display over the stage area to capture, set its resolution to match the LED processor input, and use its output as the feed. This gives precise control over which part of the stage content reaches each section of the wall.

This is especially useful for:

• LED walls with non-standard aspect ratios or unusual tile layouts
• Configurations where content is designed on a wide horizontal stage but must be split or remapped to individual processor inputs
• Setups using a wall processor that expects specific input resolutions from the media server

Content Compositing

Virtual displays enable layered compositing workflows. Because a virtual display's rendered output can be used as a media source, you can:

• Build a complex animation or multi-layer composition on one timeline
• Capture its result via a virtual display
• Use that result as a single media source on another timeline or display

This keeps timelines clean and allows reusable pre-composed elements.

3D Projection Mapping

When mapping content onto 3D geometry, virtual displays can act as viewpoints that capture specific faces or sections of a model. The captured output is then routed to the corresponding physical projector or display that covers that geometry.

Multi-Format Output

Virtual displays adapt content layout to match different output formats. For example, over a single wide panoramic composition, overlay multiple virtual displays — each capturing a different section at the resolution required by its destination processor or screen.

Adding a Virtual Display

You can create virtual displays from multiple places in the interface:

• Stage → Add Virtual Display — adds at a default location
• Right-click in Stage → Add Virtual Display — adds at the clicked position
• Devices window → Add Virtual Display — useful when managing device lists directly

New virtual displays are automatically named in sequence (for example Virtual Display 1, Virtual Display 2). The default resolution is 1920 × 1080 with Use as Input Resolution enabled.

Initial Configuration

After creating a virtual display, configure these properties in the Device Properties panel:

• Name — a clear label that describes its purpose
• Resolution — match the expected input resolution of the downstream device (LED processor, capture, etc.)
• Stage placement — position and size the display to capture the intended stage area
• Stage tiers — assign tier visibility if your show uses tier-based filtering

Using a Virtual Display as a Media Source

A key capability of virtual displays is that their rendered output can be used as a media source for cues on other timelines or displays. This enables multi-stage compositing where one display's full render becomes a single input element elsewhere.

To use a virtual display as a media source:

1. Create a media cue on the target timeline.
2. Assign the virtual display as the cue's media source (drag the virtual display from the Devices window to the timeline).
3. The cue's dimensions automatically match the virtual display's width and height.

Cues that use a virtual display as their media source are always live — they do not have playback controls such as in-time, looping, or free-running. The content updates in real time as the virtual display renders.

Rendering Details

Virtual displays use high precision for compositing so they can be reused as inputs to other displays without visible quality loss.

They support output delay (0–10 frames) for frame buffering. Warp, blend, and white point correction are applied as post-processing passes, just as they are on physical outputs.

NDI® is a registered trademark of Vizrt NDI AB.