INSTALLATION AND OPERATION

TABLE OF CONTENT

BEFORE USING YOUR WATCHPAX 30

Please read the manual thoroughly before operation. Always check that the unit has not been damaged in transit when you take delivery. >IMPORTANT: The WATCHPAX 30 is a plug-and-play unit. Do not open, modify or repair the unit yourself. Opening, modifying (software or hardware) or repairing the unit yourself willl invalidate the warranty and presents a risk for the user.

SAFETY FIRST

  • Insert the power plug all the way in, so it is not loose.
  • Do not place the power cord or product near heat sources.
  • Caution: shock hazard if handled carelessly or inaccurately.
  • The unit shall be connected to a grounded outlet.
  • Do not use a damaged power cord or plug.
  • Do not touch the power plug with wet hands.
  • Do not install the product in a narrow space and/or where there is bad ventilation. Do not block the ventilation in any way when operated.
  • Always keep plastic packaging away from children.
  • Do not install the product on an unstable or vibrating surface.
  • Install the unit in a clean, dry area without excessive particles or dust, in the air (preferably in an air-conditioned server room). Do not install the product in a place where it is exposed to high temperature, chemicals, dust, moisture, oil or smoke as this may seriously affect its performance and lifetime.
  • Take care not to drop the product when moving it.
  • When installing the product on a shelf, ensure the bottom edge of the product does not protrude to avoid tipping, for example.
  • To move the product, first disconnect all the cables from it.
  • The wall socket should be easily accessible for pluggable equipment.
  • High voltage runs through the product. Do not attempt to disassemble, repair, or modify the product on your own.
  • If the product generates a burning smell, or smoke, remove the power cords immediately and contact Dataton.
  • If the product falls, or the exterior is damaged, power off the product, remove the power cords and contact Dataton.
  • If there is a risk of thunderstorm or lightning strike, turn off the power and disconnect all cables.
  • Do not insert a metallic object or inflammable object into any opening of the product.
  • Unplug this product from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the product. Use a microfiber cloth for cleaning.
  • After storage in cold conditions, let the product adapt to normal temperature for two hours before powering on.

VENTILATION

Airflow is critical for the correct operation of WATCHPAX 30. Do not stack units or place any items on top of the WATCHPAX 30.

In any installation, there should always be a minimum of 200 mm clear space at front and 200 mm above the unit.

WP30

INSTALLATION

GENERAL

  • This equipment is for professional use for installation at locations where only adults are normally present. Check the “Safety First” list before use.
  • The WATCHOUT 30 must be connected to a properly grounded wall socket (a socket-outlet with protective earth connection in the building).
  • The serial number is located on the base of the unit.

IMPORTANT: Only use the power cord supplied with the WATCHPAX 30 unit, otherwise Dataton AB cannot guarantee full functionality.

STANDALONE INSTALLATION

Place the unit flat on its base. The base is the side of the unit showing the serial number and Dataton logo.

POWER ON

The unit is switched on by inserting the power cord or inserting the power cord and using the on/off switch. The discreet on/off switch is located behind the front plate of the WATCHPAX 30 (see Connectors in the Introduction). >IMPORTANT: Use a pencil or similar insulated tool to press the on/off switch. Do not use a metal implement.

FIRST POWER ON

The first time you power up a WATCHPAX 30 (after delivery or after a reset) the system will finalize installation and reboot several times. This procedure will typically take about 5 minutes to complete.
>IMPORTANT: Do not interrupt this procedure.

POWER OFF

Powering down should be initiated from within WATCHOUT production/Producer software or by using the on/off switch.

When the power-off sequence is complete, the fans will turn off, and the power cord may be removed.

NOTE: If you need to perform a forced shutdown, unplug the power cord to turn off the unit.

QUICK START

  • Connect displays to the WATCHPAX 30 using the HDMI outputs.
  • Connect the WATCHPAX 30 to the network using the Ethernet port.
  • Power up the WATCHPAX 30.
  • Start WATCHOUT software on the production computer which is on the same network. Make sure you are using WATCHOUT version 7, or WATCHOUT version 6.7.3, or higher.

RESET WATCHPAX 30

There are occasions when you may want to reset a WATCHPAX 30, for example, if the unit has been corrupted, or if it is a rental unit and user-specific info has to be removed between rentals. There are two levels of reset:

  • Reset and keep user data. This resets the operating system, display, GPU and capture settings but retains user data, such as shows and media.
  • Reset to factory settings. This takes the unit all the way back to the original factory settings and you lose all user data.

IMPORTANT: A reset, regardless of level, is an advanced measure. Make sure you are fully aware of what data you lose when you reset!

RESET AND KEEP USER DATA

This option resets the system partitions but keeps all user data such as:

  • Shows
  • Media
  • WATCHOUT settings
  • Startup script
    • Network settings
    • Timecode settings

Driver-related settings will be reset to default factory settings such as:

  • Display settings
    • Display mode

RESET TO FACTORY SETTINGS

This resets all partitions to factory settings and all user data will be lost. This level of reset is suitable when you want to remove all settings between projects.

RESET PROCEDURE

The reset menu is hidden by design in order to avoid accidental resets or misuse. To reset your WATCHPAX 30 device, follow these steps:

  1. Power off the WATCHPAX 30.
  2. Disconnect any USB devices.
  3. Now connect a keyboard to one of the USB ports.
  4. Connect at least one display device to an HDMI output.
  5. Power on the WATCHPAX 30.
  6. During startup, you will see a five-second countdown in the top left corner of the display. Press Esc during this countdown.

WP30

NOTE: If you don’t see a counter, it means the display device is slow to lock to the output. In that case, press Esc repeatedly after power-on to move to the menu below.

  1. Select the desired reset option in the menu that appears, and press Enter. >IMPORTANT: There will be no confirmation – the reset process starts immediately!

WP30

  1. As noted above, the reset process starts immediately, providing some visual feedback.

WP30

  1. The WATCHPAX 30 will restart several times in order to configure the operating system and hardware.

WP30

IMPORTANT: Do not power off the unit during the configuration process!

  1. WATCHOUT will start when the process is complete. The system image version will be appended after the serial number.

WP30